![]() ![]() ![]() You will see the color of the person change to match the background. In earlier versions use Image>Adjustments>Match ColorĬhoose the Harmonization option, by clicking the slider in Photoshop 2022 and newer. In Photoshop 2022 and newer choose Filter>Neural Filters Make sure the persons layer is the currently active layer. Step 4 Matching Colors between person and backgroundĬurrently the color tones and saturation are different from the person from the new background. When you are happy with the size and position, press Enter to apply the transformation. (Alt/Option + scroll wheel on mouse).ĭrag the corner handle to make the person smaller. With Free Transform still active, zoom out on the image until you can see the transform handles. This will flip the person to the opposite direction, so that the light is coming from the correct side. Let’s flip the person and change the size. It’s going he opposite direction on the person. Notice the angle of the sun on the background photo. Step 3: Matching the lighting of the layers We need to make the new layer match the background. This tutorial shows the basics of combining photos.ĭrag your cursor into the middle of the photo and let go. Wait for the image to open, don’t let go yet. We need to combine this photo with the new background.Ĭlick down and hold, drag the photo up to the tab of the image we are moving the photo into. You will now see our image with the background removed. Turn on Decontaminate Colors and choose “New Layer with Layer Mask” from Output. ![]() Here is a tutorial and tips on the refine brush. Use the refine brush on the edges to make them better. If there are no jaggy edges skip this step. If you see jaggy edges where it should be smooth, add some feather and contrast to smoothen it out. This is where we make the selection edges better. You will see a selection around the person (CS6, make the selection with quick selection tool).Ĭlick Select and Mask from the top. For older versions, use the quick selection to cut out the person. ![]() Use a photo of the person you want to transport into the new photo.Ĭhoose the object selection tool in newer versions of Photoshop. Watch the quick video above to see all the steps in action. There are a few key steps to this tutorial. Here we have the Eiffel Tower and we want add add a person as if they were there. This tutorial is created for the newest versions of Photoshop (2022+) but it will work on all versions. This is a simple tutorial, but it will touch on everything you need to know to convincingly put a person into a photo. If it drives out of the road in a low contrast zone one can undo the last segment and click manually the right route.In this Photoshop tutorial we will put a person into a photo. The Scissors can be substantially faster than drawing a path if there's a visible edge that can be followed. Actually it makes directly the selection. The easiest idea is to extend the hairs with the smudge tool.Īutomatic edge tracing would be fine when one draws a path only approximately right. Making it look plausible needs plenty of practicing. But getting it right indoors doesn't happen without perfectly set lights and background.įurry, fluffy or bushy edge clipped with far too simple path can be often fixed by redrawing it. Numerous photos for successful background removal have been shot on the beach. High cost studio gear (except a good camera) is not a must. But 99,9% of the job was done in the photo shooting session. You can find easily tens of examples where one removes the background of hair with easy looking few clicks. The lights and background must be specially selected to make on color and contrast based background removal possible. Those cases need preparations before taking the photo. In difficult cases (fluffy, furry, bushy) drawing path will not give good results, because nobody has enough time and patience for the job. The hair and beard have easy edges, but the path may still need 100 nodes or even more: Keep the original image layer until you are sure it's not needed. Copy and paste the object to a new layer. It hangs around if you save the file as XCF.Ĭonvert the path to selection (=add to selection). When the path is ready it should be saved - one can find a way to use it or something can be noticed later. In addition the path can be edited afterwards. Fortunately an error during the drawing can be undone by pressing Ctrl+Z. Drawing them fast needs plenty of practicing. A waterproof 100% manual method for images with edges this simple is to draw a path around the object:Īs you see the path has also curved segments. The edge can be seen by humans and also by advanced semiautomatic selection methods. But it doesn't have fuzzy edges such as big bushy hair or beard where the background can partially be seen through. I guess you selected intentionally a photo where the magic wand and other on color and contrast based selection methods fail. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |